Well water hardness in Logan County, Kentucky
14 gpg very hard
Private wells in Logan County typically give very hard water: the median well sampled by the U.S. Geological Survey has 14 gpg (240 mg/L as CaCO₃).
Wells differ a lot, even next door: one in ten sampled wells had less than 127 mg/L and one in ten more than 405 mg/L. The figure comes from 18 wells and 19 samples taken between 1980 and 1982 (half of them by 1982).
Most samples are older than ten years. Groundwater hardness comes from the rock the well is drilled into and changes slowly, but your own well can be quite different, so treat this as a regional indication and test your water.
What this hardness means for a well household
- Severe scale: heater elements and washing-machine heaters fail early.
- Detergent use is very high; taps and screens coat within days.
- Dishwasher at maximum salt setting.
- An ion-exchange softener is practically essential; RO for drinking water.
How to test your well in Kentucky
Hardness is only one part of a well test. Federal health agencies advise every private well owner to test regularly:
- Test a private well every year for total coliform bacteria, nitrates, total dissolved solids and pH; test more often if young children, older adults or a pregnant or nursing person live in the home. (US EPA, Protect Your Home's Water)
- Test at least once a year and ask the local health department which other germs or chemicals matter where you live. (CDC, Guidelines for Testing Well Water)
- Test the well for bacteria every year at a certified drinking water laboratory, and test for other contaminants after a pregnancy or new infant, a change in taste or smell, or a contaminant found in a neighbor's water. (Kentucky Division of Water, Groundwater protection: wells (June 2024))
Your county health department can tell you which certified laboratories accept private well samples.
A new well for potable use must be analyzed for E. coli within 30 days of completion (401 KAR 6:310, Section 9(6)); no rule for existing wells was found.
If no local lab suits you, mail-in kits from certified labs test a wider panel at home; they cost more than a state or county lab.
Treating hard well water
At this hardness an ion-exchange softener sized for your household is the usual answer. Test iron, manganese and pH first: well water often needs an iron filter or a pH correction in front of the softener.
Nearby counties
FAQ
How hard is well water in Logan County, Kentucky?
The median well sampled by the USGS in Logan County has 14 gpg (240 mg/L as CaCO₃), which is very hard. One in ten wells had less than 127 mg/L and one in ten more than 405 mg/L.
Is my own well the same?
Not necessarily. Hardness depends on the rock layer your well draws from and on its depth, so neighbouring wells can differ by a factor of two or more. Only a test of your own water tells you.
How often should I test my well in Kentucky?
Every year for coliform bacteria, nitrate, total dissolved solids and pH (EPA and CDC advice), and after floods, repairs or a change in taste or smell. Hardness, iron and manganese once, and again before you buy a softener.
Do I need a water softener for my well?
Yes, unless you are only passing through: scale damages appliances within a few years.
Where does this figure come from?
From 19 samples of 18 wells measured by the U.S. Geological Survey between 1980 and 1982, retrieved from the Water Quality Portal. We publish a county only when at least 10 wells were sampled.
Source and method
Computed by Water Hardness Atlas from USGS National Water Information System samples (characteristic "Hardness, Ca, Mg", sites of type well, samples since 1980), retrieved 2026-10-29 through the Water Quality Portal. For each well we take the median of its samples, then the median of all wells in the county; wells above 1,000 mg/L (oil, gas or mine brines) are left out. USGS data are in the U.S. public domain. Water Quality Portal query
Well water hardness in Kentucky → · Kentucky: tap water by city →