Well water hardness in Roosevelt County, New Mexico
13.8 gpg very hard
Private wells in Roosevelt County typically give very hard water: the median well sampled by the U.S. Geological Survey has 13.8 gpg (236 mg/L as CaCO₃).
Wells differ a lot, even next door: one in ten sampled wells had less than 177 mg/L and one in ten more than 637 mg/L. The figure comes from 30 wells and 75 samples taken between 2001 and 2023 (half of them by 2006).
Most samples are older than ten years. Groundwater hardness comes from the rock the well is drilled into and changes slowly, but your own well can be quite different, so treat this as a regional indication and test your water.
What this hardness means for a well household
- Severe scale: heater elements and washing-machine heaters fail early.
- Detergent use is very high; taps and screens coat within days.
- Dishwasher at maximum salt setting.
- An ion-exchange softener is practically essential; RO for drinking water.
How to test your well in New Mexico
Hardness is only one part of a well test. Federal health agencies advise every private well owner to test regularly:
- Test a private well every year for total coliform bacteria, nitrates, total dissolved solids and pH; test more often if young children, older adults or a pregnant or nursing person live in the home. (US EPA, Protect Your Home's Water)
- Test at least once a year and ask the local health department which other germs or chemicals matter where you live. (CDC, Guidelines for Testing Well Water)
- Test every spring for coliform bacteria, nitrate and arsenic, and every five years for uranium; also test after a new well is installed, when buying a home with a private well, and after a flood, wildfire, septic failure or sudden change in taste, colour or odour. (New Mexico Environment Department, Guidance for Owners of Private Wells)
Use a certified laboratory: NMED Drinking Water Bureau, Guidance for Owners of Private Wells (links the list of certified laboratories).
New Mexico does not regulate private wells; NMED's testing guidance consists of recommendations, not regulatory requirements.
If no local lab suits you, mail-in kits from certified labs test a wider panel at home; they cost more than a state or county lab.
Treating hard well water
At this hardness an ion-exchange softener sized for your household is the usual answer. Test iron, manganese and pH first: well water often needs an iron filter or a pH correction in front of the softener.
Nearby counties
FAQ
How hard is well water in Roosevelt County, New Mexico?
The median well sampled by the USGS in Roosevelt County has 13.8 gpg (236 mg/L as CaCO₃), which is very hard. One in ten wells had less than 177 mg/L and one in ten more than 637 mg/L.
Is my own well the same?
Not necessarily. Hardness depends on the rock layer your well draws from and on its depth, so neighbouring wells can differ by a factor of two or more. Only a test of your own water tells you.
How often should I test my well in New Mexico?
Every year for coliform bacteria, nitrate, total dissolved solids and pH (EPA and CDC advice), and after floods, repairs or a change in taste or smell. Hardness, iron and manganese once, and again before you buy a softener.
Do I need a water softener for my well?
Yes, unless you are only passing through: scale damages appliances within a few years.
Where does this figure come from?
From 75 samples of 30 wells measured by the U.S. Geological Survey between 2001 and 2023, retrieved from the Water Quality Portal. We publish a county only when at least 10 wells were sampled.
Source and method
Computed by Water Hardness Atlas from USGS National Water Information System samples (characteristic "Hardness, Ca, Mg", sites of type well, samples since 1980), retrieved 2026-10-29 through the Water Quality Portal. For each well we take the median of its samples, then the median of all wells in the county; wells above 1,000 mg/L (oil, gas or mine brines) are left out. USGS data are in the U.S. public domain. Water Quality Portal query