Well water hardness in Mountrail County, North Dakota
11.1 gpg very hard
Private wells in Mountrail County typically give very hard water: the median well sampled by the U.S. Geological Survey has 11.1 gpg (190 mg/L as CaCO₃).
Wells differ a lot, even next door: one in ten sampled wells had less than 12 mg/L and one in ten more than 800 mg/L. The figure comes from 55 wells and 81 samples taken between 1982 and 2023 (half of them by 1992).
Most samples are older than ten years. Groundwater hardness comes from the rock the well is drilled into and changes slowly, but your own well can be quite different, so treat this as a regional indication and test your water.
What this hardness means for a well household
- Severe scale: heater elements and washing-machine heaters fail early.
- Detergent use is very high; taps and screens coat within days.
- Dishwasher at maximum salt setting.
- An ion-exchange softener is practically essential; RO for drinking water.
How to test your well in North Dakota
Hardness is only one part of a well test. Federal health agencies advise every private well owner to test regularly:
- Test a private well every year for total coliform bacteria, nitrates, total dissolved solids and pH; test more often if young children, older adults or a pregnant or nursing person live in the home. (US EPA, Protect Your Home's Water)
- Test at least once a year and ask the local health department which other germs or chemicals matter where you live. (CDC, Guidelines for Testing Well Water)
- Test a new well before use, after long non-use, when buying a home, after floods, when quality changes, and at regular intervals; a typical analysis is a bacterial test, general chemistry and nitrate, with arsenic or trace metals optional. (North Dakota DEQ, Private Well Owner's Guide: Well Water Testing (April 2026))
Your county health department can tell you which certified laboratories accept private well samples.
Testing is your own responsibility: no state agency samples existing private wells routinely.
If no local lab suits you, mail-in kits from certified labs test a wider panel at home; they cost more than a state or county lab.
Treating hard well water
At this hardness an ion-exchange softener sized for your household is the usual answer. Test iron, manganese and pH first: well water often needs an iron filter or a pH correction in front of the softener.
Nearby counties
FAQ
How hard is well water in Mountrail County, North Dakota?
The median well sampled by the USGS in Mountrail County has 11.1 gpg (190 mg/L as CaCO₃), which is very hard. One in ten wells had less than 12 mg/L and one in ten more than 800 mg/L.
Is my own well the same?
Not necessarily. Hardness depends on the rock layer your well draws from and on its depth, so neighbouring wells can differ by a factor of two or more. Only a test of your own water tells you.
How often should I test my well in North Dakota?
Every year for coliform bacteria, nitrate, total dissolved solids and pH (EPA and CDC advice), and after floods, repairs or a change in taste or smell. Hardness, iron and manganese once, and again before you buy a softener.
Do I need a water softener for my well?
Yes, unless you are only passing through: scale damages appliances within a few years.
Where does this figure come from?
From 81 samples of 55 wells measured by the U.S. Geological Survey between 1982 and 2023, retrieved from the Water Quality Portal. We publish a county only when at least 10 wells were sampled.
Source and method
Computed by Water Hardness Atlas from USGS National Water Information System samples (characteristic "Hardness, Ca, Mg", sites of type well, samples since 1980), retrieved 2026-10-29 through the Water Quality Portal. For each well we take the median of its samples, then the median of all wells in the county; wells above 1,000 mg/L (oil, gas or mine brines) are left out. USGS data are in the U.S. public domain. Water Quality Portal query
Well water hardness in North Dakota → · North Dakota: tap water by city →